This thread for LG G2 Unlocking band for AWS. To make it work with WIND/Mobilicity. I used the Telus D803 model. Other Canadian models might be similar.
As always try this at your own risk. If you brick your device missing or adding any steps its you! messing it up!
Lot of threads on enabling this feature is confusing for this model. Finding the right information is a wild search! The following thread is clean and great:
http://forum.xda-developers.com/onep...lcomm-t2877031
Wind (AWS) enabled in Telus LG G2 D803 model and is working great. Basically rolled back to Stock ROM (4.4.2), Rooted, Enabled developer-debug mode & finally for enabled Modem mode used 'Tethering' option checked in LG stock. ROM which pops in phone whenever its connected to computer. NO ADB or terminal commands, whatsoever. Check if diag is enabled by entering in dialer => 3845#*803# and going to USB Info => USB basic info. You should see the line 'functions' has diag displayed. (Note: 803 in above dialer command since its D803 Canadian model. Replace it with your sub-model number for any other G2, ATT, Tmo etc).
Once above done, connect to computer and proceed further steps.
For Windows: When connecting to computer the NDIS network adapter might interfere with your network connection. (Since modem is enabled in phone and its now tethered to computer). Just go to network settings and disable NDIS network adapter if you are using that computer for browsing as well.
Once above is done, just follow from Step 7 of above thread. Instead of HTC Modem, it will be listed as "LGE AndroidNet USB Serial Port (COMx)". For me it was COM5 for COMx. It might vary. The appropriate LG drivers needs to be installed. (Search for LGUnitedMobileDriver)
In the above thread, once in RF_NV_Manager application the line 1877 displayed a value of 82314112. I replaced to 115868544, just enabling the Wind 1700 AWS band additionally. Saved value, rebooted phone. After restarting connected in the same procedure and verified the value is saved properly by re-reading the values from phone.
Inserted SIM, though initially it didn't display WIND (On Network search) after some 15 mins it automatically connected to Wind and now Wind network comes in network search.
Works great! Thanks for all the guidance in the forums. Hope helps someone.
As always try this at your own risk. If you brick your device missing or adding any steps its you! messing it up!
Lot of threads on enabling this feature is confusing for this model. Finding the right information is a wild search! The following thread is clean and great:
http://forum.xda-developers.com/onep...lcomm-t2877031
Wind (AWS) enabled in Telus LG G2 D803 model and is working great. Basically rolled back to Stock ROM (4.4.2), Rooted, Enabled developer-debug mode & finally for enabled Modem mode used 'Tethering' option checked in LG stock. ROM which pops in phone whenever its connected to computer. NO ADB or terminal commands, whatsoever. Check if diag is enabled by entering in dialer => 3845#*803# and going to USB Info => USB basic info. You should see the line 'functions' has diag displayed. (Note: 803 in above dialer command since its D803 Canadian model. Replace it with your sub-model number for any other G2, ATT, Tmo etc).
Once above done, connect to computer and proceed further steps.
For Windows: When connecting to computer the NDIS network adapter might interfere with your network connection. (Since modem is enabled in phone and its now tethered to computer). Just go to network settings and disable NDIS network adapter if you are using that computer for browsing as well.
Once above is done, just follow from Step 7 of above thread. Instead of HTC Modem, it will be listed as "LGE AndroidNet USB Serial Port (COMx)". For me it was COM5 for COMx. It might vary. The appropriate LG drivers needs to be installed. (Search for LGUnitedMobileDriver)
In the above thread, once in RF_NV_Manager application the line 1877 displayed a value of 82314112. I replaced to 115868544, just enabling the Wind 1700 AWS band additionally. Saved value, rebooted phone. After restarting connected in the same procedure and verified the value is saved properly by re-reading the values from phone.
Inserted SIM, though initially it didn't display WIND (On Network search) after some 15 mins it automatically connected to Wind and now Wind network comes in network search.
Works great! Thanks for all the guidance in the forums. Hope helps someone.
did this and lost ability to connect with QPST and imei is now unknown lol :S
RépondreSupprimer